国产一区二区三区在线看-国产一区二区三区在线免费-国产一区二区三区在线免费观看-国产一区二区三区在线视频-亚洲视频中文字幕在线-亚洲视频自拍

Always keep the switch and panel clean. You can stick a layer of protective film on the buttons of controller panel to avoid sharp and anti-corrosive objects from touching the panel.

T Automatic tool setting

G53 Machine Coordinate System

G54 G55 G56 G57 G58 User Coordinate System

S12000 Spindle speed is 12000rpm

M03 Spindle rotates in forward direction

M05 Spindle stops running

M08 Cutting oil on

M09 Cutting oil off

M54 Set the XY value of machining origin G54

M56 Set Z value of G54 machining origin

M57 Modify (increase / decrease) the Z value of G54 machining origin

M66 M77 Set X value of machining origin G54

M88 M99 Set Y value of machining origin G54

M100 Exchange XYZ values of G54 and G55

M101 Exchange XYZ values of G54 and G56

M102 Exchanges XYZ values of G54 and G57

NAME: NEW，

MODEL: 8050M | 8055M，

TYPE: SERIAL LINE，

CONNECT ON STARTUP: □，

PORT: COM1 or COM2，

BAUDRATE: 38400Bd，

WORK FOLDER: Select the folder to which the NC program is connected.

CNC OPERATOR’S WORK FOLDER: Select the folder to which the NC program is connected.

a. Every time the machine starts, it must be returned to zero (speed down before returning to zero to avoid collision).

b. When installing the tool, the spindle nut, collet chuck, tool and inner hole of the spindle must be kept clean. Do not use worn, deformed, or damaged collet chuck and spindle nut. Minimize the length that the tool extends beyond the collet chuck when clamping the tool.

c. When tightening the spindle nut, excessive tightening torque will damage the spindle, spindle nut, collet chunk and spindle wrench. Different chucks are recommended to be locked according to the corresponding tightening torque below: ER11=2.0Kgf.m，ER16=4.0Kgf.m，ER20=6.0Kgf.m ER20=6.0Kgf.m，ER25=6.0Kgf.m，ER32=7.0Kgf.m.

d. When the spindle nut is loosened, the collet will loosen at the same time. The tool must be grasped to prevent falling damage.

e. Slow down the feed rate before executing tool setting command. On the premise that the machine does not collide during the tool setting movement, the tool setting can be completed automatically by increasing the movement rate. It is forbidden to perform tool setting operation when the spindle is running. During tool setting, the detection surface of tool sensor must be clean and free of foreign objects and cuttings. When performing tool setting operation, avoid excessive tool length so as not to collide with the tool sensor.

Pressure of pressure gauges for engraving and milling machine: Pressure of AR2000-02 pressure reducing valve is 0.4MPa. Pressure of AR2000 pressure reducing valve is 0.4MPa. Pressure of AR2001-02G pressure reducing valve is 0.4MPa.

The pressure of the compressed air source for the machining center is not less than 0.7MPa. The working pressure of the air source processing device of the machine tool is 0.6MPa.

Over more than 10 years effort, JIATIE has grown as a famous brand and a famous enterprise in machine tool industry. The service network spreads over more than 40 cities to provide all-round service. The products have been exported to strong industrial countries such as Germany, the U.K, Japan, etc. JIATIE will make unremitting efforts for cutting-edge technology, top-notch product and considerate service to win the trust of more and more customers.